Jump to content
  • Welcome!

    Welcome to BARCS forums, full of great information and ideas about your favourite hobby . Please register if you'd like to take part.

Electric Soaring and F5J

A forum to discuss electric powered soaring and F5J

Subforums

  1. F5J GBR Team Talk

    This forum is for current F5J UK Team members to discuss Championship events and arrangements. Please PM Austin to gain access.

    • No posts here yet

448 topics in this forum

  1. BARCS -ELG at Dartford Kent May 20th 2018

    • 11 replies
    • 851 views
  2. Fosa Electro Layup Selection

    • 4 replies
    • 475 views
  3. Horsham F5J May 13th entries open 1 2

    • 31 replies
    • 2,120 views
  4. Nats 2018 schedule

    • 0 replies
    • 319 views
  5. BARCS-ELG 6thMay 2018 1 2

    • 34 replies
    • 1,872 views
    • 8 replies
    • 553 views
  6. Altis 4 problems

    • 2 replies
    • 344 views
  7. F5J 2018 Southern Area

    • 4 replies
    • 1,466 views
  8. BARCS-ELG 29thApril 2018 CANCELLED

    • 18 replies
    • 909 views
    • 12 replies
    • 652 views
    • 57 replies
    • 3,205 views
  9. Pre-Season F5J/ELG Sunday 25th March at Little Bentley Park 1 2 3

    • 50 replies
    • 2,811 views
  10. Altis V4

    • 6 replies
    • 648 views
  11. New Model Advice

    • 4 replies
    • 700 views
  12. CIAM

    • 0 replies
    • 401 views
  13. CHANGE BARCS ELG RULES 1 2

    • 34 replies
    • 2,645 views
  14. Jaro Muller Esprit Electric Conversion

    • 16 replies
    • 1,237 views
  15. Loire Valley F5J

    • 4 replies
    • 634 views
  16. Taped on wings

    • 6 replies
    • 513 views
  17. Optimus F5J extra Light 1 2

    • 21 replies
    • 2,472 views
  18. F5J flying field

    • 6 replies
    • 502 views
  19. Delphin by Aer-O-Tec

    • 9 replies
    • 1,177 views
  20. Height limiter, data logger?

    • 1 reply
    • 463 views
  21. Red Fox motors

    • 3 replies
    • 747 views
  22. F5J International team selection 2018

    • 9 replies
    • 1,287 views
  • Who's Online   11 Members, 0 Anonymous, 25 Guests (See full list)

    • paulorenato123
    • MAZ
    • Jess
    • Jonathan Gough
    • epler205
    • timboiow
    • sorry
    • Redbird
    • Ville56
    • Steve J
    • fpljohn
  • Upcoming Events

    No upcoming events found
  • Topics

  • Vendor Topics

  • Today's Birthdays

    No users celebrating today
  • Posts

    • Redbird
      A bicycle chain link extractor pushes the rivets out but still too large for this job. I think a pin punch is what you need though I don't have one. They have nice flat ends. You could perhaps use a ground drill bit rather than wire. 
    • oipigface
      There are two grub screws in these, and three threaded holes for them to fit in. The middle hole is to secure the pin, the other two are for the splines. Two are needed so that the screw is accessible whichever way the servo is oriented. This one is new, so there is no question of glue.  I had a look on the web for pin pushers. There seem to be two kinds. One is for pushing pins accurately into a piece of wood or board, the other for applying many tonnes of pressure to the enormous pins in caterpillar tracks. I thought there might be something like the latter (only smaller) that I could use. Otherwise it’s back to wire and hammer.
  • Member Statistics

    • Total Members
      1,535
    • Most Online
      1,037

    Gliderchuck
    Newest Member
    Gliderchuck
    Joined
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.