Jump to content
  • Welcome!

    Welcome to BARCS forums, full of great information and ideas about your favourite hobby . Please register if you'd like to take part.

F3K and Handlaunch

Discuss anything to do with F3K and Handlaunch Gliders.

406 topics in this forum

  1. 2019 Dates 1 2

    • 21 replies
    • 1,624 views
    • 19 replies
    • 475 views
    • 3 replies
    • 125 views
  2. Help CX5. Tailplane mount

    • 0 replies
    • 40 views
    • 0 replies
    • 60 views
  3. Learning the hard way

    • 7 replies
    • 262 views
  4. UK F3K Eurotour & World Cup 2019 1 2 3 4

    • 79 replies
    • 2,742 views
  5. Wooden Transport Box

    • 5 replies
    • 304 views
  6. Vest Pokal 2019 1 2

    • 20 replies
    • 1,011 views
  7. Stream NXT 1 2 3 4 10

    • 189 replies
    • 15,315 views
  8. Workshop Model Stand

    • 0 replies
    • 95 views
  9. Radioglide 2019

    • 8 replies
    • 231 views
    • 0 replies
    • 48 views
    • 28 replies
    • 1,129 views
    • 21 replies
    • 585 views
  10. BAMF boom repair 1 2

    • 23 replies
    • 440 views
    • 0 replies
    • 64 views
    • 99 replies
    • 3,638 views
    • 4 replies
    • 197 views
    • 1 reply
    • 142 views
    • 4 replies
    • 207 views
    • 8 replies
    • 427 views
  11. Newbie questions!

    • 8 replies
    • 186 views
  12. Help needed for dlg build thread 1 2

    • 28 replies
    • 788 views
    • 8 replies
    • 274 views
  • Who's Online   9 Members, 0 Anonymous, 20 Guests (See full list)

    • CTR
    • DerekC
    • Bobbyr
    • campsieflyer
    • Mark Evans
    • robtc3uk
    • Kyri
    • chuckit
    • Munch197
  • Upcoming Events

  • Topics

  • Vendor Topics

  • Today's Birthdays

    1. Richardjb
      Richardjb
      (67 years old)
    2. Skip
      Skip
      (44 years old)
  • Posts

    • oipigface
      Since we are talking about servo installation, here are a couple of photos of a frame that has taken me about a day to program into my CNC router. It’s for my Personal Best Pitbull, which is having all its electronic bits and pieces replaced. I’ve considered upgrading to HV, but this got complicated and in the end I decided to install new  Futaba S3150’s, but only after I had ripped out the original  frames. The design is basically the Baudis original, reinterpreted because I couldn’t source any 5mm ply. This is made of 6mm ply, which has to be routed out so that the 10mm thick servo sits flush to the bottom. The bearing frame (which is a Baudis original) also sits flush to the bottom. I’m pleased with the way that it turned out. It’s the most complicated piece I’ve made with the router, and the remaining three will take less than 10 minutes each to produce. Along the way, I also programmed a frame for the MKS HBL6625. Servos are removed by undoing the screws that eventually will fit in the holes you can see. Probably could be done on the field if necessary.  
    • Munch197
      Price reduced £120 posted
  • Member Statistics

    • Total Members
      1,439
    • Most Online
      900

    Theflyingric
    Newest Member
    Theflyingric
    Joined
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.