Jump to content
thermaldoctor

Pike Precision 2 arrive 😎

Recommended Posts

thermaldoctor

20200731_155653.thumb.jpg.1775a955f97a8bb1b87c6fc770812477.jpg

4 Pike Precision 2's have just landed at Flightech HQ.

Unboxing later tonight...

  • Like 2

Share this post


Link to post
Share on other sites
thermaldoctor

20200731_185550.thumb.jpg.8a55a38db0af8f7af3789e5be0069885.jpg

Unboxed. Went together like Lego.

These are the two colour schemes i will settle on for stock models unless anyone has any suggestions. Lots of other colour schemes available to order..

20200731_190146.thumb.jpg.2e19c2c74dd280ff6d7179465abba432.jpg

The Pre-installed LDS is not a system i am familiar with until now. Only used to Servorahman IDS. Seems very good i like it. Saves a load of hassle that's for sure...

  • Like 4

Share this post


Link to post
Share on other sites
thermaldoctor

Kingmax CLS0612W going in sweet as a nut on the ailerons. Lots of movement and no buzzing at neutral. 

Like for servorahmen IDS, the Samba LDS horns are a tight fit so had to remove the tightening screw and gently open up the clamp and wiggle the servos in. When done the screw can be re-fitted and clamped up for an extremely secure set up. The output horns on the Kingmax are identical to KST. When i used to sell KST the IDS horns were an equally tight fit on the KST output gears. Better this way than sloppy horns.

Short 50mm leads make for a neat clean finish

20200801_113833.thumb.jpg.0e6c72824fef7e13cf8ee6ec1aff97c5.jpg

  • Like 2

Share this post


Link to post
Share on other sites
thermaldoctor

Flap servos in. I am really impressed with the Samba LDS system. It is very smooth, rigid and slop free. Very impressed. And the geometry is perfect. Flap servos need only a few percent here and there for symmetrical crow flap movement.

20200804_211200.thumb.jpg.6c373f22aa239e290885fa4189ca1ec4.jpg

Only criticism is the inital fitment of the spline into the hub. It is a bit tight and you need to wiggle the servo in and use a bit of force. But once you get the servo horn in once the next time (s) become very easy. I think this is due to newly machined servo output splines going into newly machined LDS hubs. Both will have crisp sharp machined 90 degree edges. Once these get edges get slightly rounded and chamfered from the initial fitment the horns then slot in beautifully.

 

  • Like 1

Share this post


Link to post
Share on other sites
thermaldoctor

Next batch of Precision 2's in September  will be the last ones with free wing & fuselage bags and free fitted LDS system. We will still offer the best airframe price possible but the covers and bags will be at an additional cost as per normal. Thanks

Share this post


Link to post
Share on other sites
isoaritfirst

Nice to have all the wiring including the MPX plugs all done and dusted.  

Fixed into wing at factory, just need fixing into fuselage wing root.

 

  • Like 1

Share this post


Link to post
Share on other sites
isoaritfirst

E750CB26-3590-4554-8F78-3F4A5F3AA406.jpeg.abd52431cd0989ec4a78decb80f57513.jpeg
KingMax servos fitted into wings. As Neil said it takes a little persuading to get the servo heads into the lds heads . New splines and no taper/lead-in makes it a trickier operation that it should be. Still a massive improvement on fitting the whole assembly yourself . Impressed by the “gearing” of the drives, it seems Samba have spent time making this just right .  
Imo too many models use of the shelf systems that are not optimised .0F3DFE80-2A25-45E7-BE57-FF18118DB983.jpeg.953442e9fd66c810805b6b52404b5110.jpeg

It is very colourful. Wiring all done and fixed into wings by Samba. Only needed to feed the wires into the fuselage and epoxy the Mpx  plugs into their corresponding fuselage recesses. No fiddling trying to line them up. They worked perfectly. Receiver plugs all nicely labelled. 
fuselage pushrods are made at tailplane and tailplane horns are in. Just have to cut servos into fuselage and make servo end of pushrods. 
waiting on delivery ofvfuselagevservos as I wanted to use the same type as in my other models. 
18650 battery pack is a fit.

install took approx a day, if servos slotted I’m easier it could be done in an evening. 
 

A2D09B44-BD5F-4221-B94B-0079982C8417.jpeg

  • Like 2

Share this post


Link to post
Share on other sites
Les

 

Received my Pike Precision 2 today.

Dry fit for a couple of pics.

Hopefully I get the time to get the radio gear over this next week and maiden it in Wales before the comp on Saturday. 

Thanks Neil/Flightech UK

20200809_194516.jpg

20200809_194546.jpg

  • Like 3

Share this post


Link to post
Share on other sites
satinet

Very nice Les. Like that scheme. 

  • Like 1

Share this post


Link to post
Share on other sites
isoaritfirst

IMG_3534.thumb.JPG.a43af41f7b19d468db2f05cb2ef965dd.JPG

 

Not the brightest of days for a maiden.

Pike added some sunshine!

Settings all transferred from my Green one using a digital angle meter.

Perfect result in the conditions yesterday (light) it immediately felt "spot on".

 

 

 

 

  • Like 4

Share this post


Link to post
Share on other sites
thermaldoctor

As standard the servo covers pre-cut out of a clear perspex acrylic type material. They are a perfect fit just needing a bit of canopy glue or thin doubled sided tape internally or clear diamond tape type stuff externally to fix in place. Whilst i would normally leave these clear to show off the kingmax servos i thought this time to spray them on the insides like an rc car bodyshell to make the samba lettering complete...

20200808_084214.thumb.jpg.65226b822af642ed532d09e889fc9c2e.jpg

20200810_215138.thumb.jpg.51d7094fe39585856cc952298a7a4077.jpg

 

  • Like 1

Share this post


Link to post
Share on other sites
Les
10 hours ago, thermaldoctor said:

As standard the servo covers pre-cut out of a clear perspex acrylic type material. They are a perfect fit just needing a bit of canopy glue or thin doubled sided tape internally or clear diamond tape type stuff externally to fix in place. Whilst i would normally leave these clear to show off the kingmax servos i thought this time to spray them on the insides like an rc car bodyshell to make the samba lettering complete...

20200808_084214.thumb.jpg.65226b822af642ed532d09e889fc9c2e.jpg

20200810_215138.thumb.jpg.51d7094fe39585856cc952298a7a4077.jpg

 

Looks good Neil 

  • Like 2

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.